CCIE RS Lab combo: TS2 DIAG2+ H2+

TS2

Q1 The HSRP status is normal on SW400, “port security” is not enabled on SW410, and “IP address dhcp” is provided on the port of User4.

Q2 The test does not increase the cost value of the SW111 to R14 ports, but reduces the values of the SW111 to R15 ports.

Q3 Probably on R22, there is no “originate” attribute in “route-map TE”. Fill in “originate” and keep in harmony with R23. When the SW210 “ping 10.1.201.254” has a route of “10.1.113.X”, the phenomenon that I am out does not seem to be this. Adding “ip ospf cost 1” on the R13 connection SW101 interface has an effect.

Q4 R20, R21 “route-map” are written, the name is “local-pref”, just hang up.

Q5 Change the ip address of R60 tunnel 0

Q6 Declare “vlan2001” on SW111, habitually plus “ipv6 unicast-routing”

Q7 The announcement of lo0 was changed on R5, “distance ospf external 210” on R10

Q8 Add “ip arp inspec trust” to the port-channel port on SW311. Check that dhcp on R30 has “lease 0 2”,no change.

Q9 Change tunnel 0 on R71, “ip ospf net point-to-m”

Q10 Add an “IP nat outside source static 201.99.70.2 201.99.25.70” to the R25. First delete an obvious error.

D2+ :(Same as SPOTO)

H2+

1.1 access ports 

1.2 trunk 

1.3 link bundling   

1.4 Jamesons’s branch offices

Jameson’s IGP: DATA center does not allow LSA 2 to appear, requires “passive vlan 101, vlan100, vlan911”, with “ospf id 1”, “router-id lo0”. The ospf of the AS65001 area seems to be all configured. Only R9 and R10 are not configured. After checking the Router id and other related information, the next step is taken. Other AS65002 areas are also configured, but the “network” method is used. R11-R14 is equipped with “default-information originate”, but the requirement is “must always advertise”, so all changes to “default-information originate” Always”.

I did not see the DR/BDR requirements. Know that you are used to configuring mpls in this step. All related ports are configured with “mpls ip”, including the “AS65006” area, but you must use lo0 to establish neighbor relationships. I have looked at all devices, “show run | se mpls” I didn’t find “mpls label pro ldp” and “mpls ldp router lo0”, so I brushed it all over.

Jacobs’ IGP: I did not see the mandatory requirement of the name JACOBS, nor did I view the phenomenon diagram of “52.52.52.52/32” on the R50, but there is a phenomenon diagram on R9 and R10, “show ip route 52.52.52.52”. Upgrade eigrp protocol to naming mode, redistribute lo52 on R52. Other operations as usual.

Redistribution requirements on R9/R10: The above said that in order to reduce the “operational cost”, do not use “access-list, ip prefix, route-map”. So as usual.

R57: BGP has been configured on R57, there is “redistribute eigrp 10”, I deleted it.

BGP: All routers in the AS65001 area have made protocols, but none of them have been configured with “router id”. I did “address ipv4” on R1, so it is more obvious to see the ipv4 route reflector. In fact, it is more convenient to see all the phenomena on R1. You can see all the vpnv4 routing entries returned by PE devices. It is much more convenient to see on R11-R14. You can also check if RD is mismatched. All RDs are Need to make up for yourself, the port is also.

AS65006 needs to delete “router bgp 65006” and use “router bgp 65001”. It is required that the configuration on the CE device cannot be changed. What else is there for NLRI? If you can’t change the configuration of the CE device, you won’t be entangled. All delete “router bgp 65006”, there is no requirement for R50, R51, R52 to establish igp relationship. The configuration of my R50-R52 is consistent with that of R3-R8, all equipped with “ipv4 next-hop-se”.

The address on R52 is wrong.

IPv6: SW3, SW4 and Lo0 have no ipv6 address, vlan 173 and R17 e0/1 have ipv6 address, but the requirement is to use ospfv3 only on SW3-4, R15-16, so you know.

It’s a tough experience to prepare CCIE RS lab, but it’s my lucky to choose SPOTO to pass my CCIE RS lab exam at first time.